Видео

ruclips.net/video/6GsdAYyY_RA/видео.htmlsi=pl0suDzAbhL5lPja there is a lot of sealant on my roof

thx

Just stop using smooth metal,textured metal is the only metal i work with,check with your suppliers, you can walk it on 8/12 an it dont oil can

I will install metal on my home no matter what. No matter what.

Im only here because Little John keeps building houses out of it, and wanted to know how realistic it is. Thanks for the informative video

caulking plus tape on the bottom?

Excellent stuff bro

thank you I appreciate this information. I live in Georgia. It rains really hard and most of the houses we have purchased. The roof doesn’t seem to be a sound as we like going into our forever home worst but thinking about switching over to a metal roof

Omg ,, too long to get it the point ..

does old dude use an oil can as microphone?

Those are awesome

We are in the process of building a barn and just noticed the horrible look of the barn with all the waviness. We asked the owners of the company to come and look at it, and I was horrified when we were basically told there was nothing we can do. We are incorporating the barn into the outside living part of our home, and I am devastated. We can't move the barn or the house (septic and water and electrical already in)---and we now get to look at the side of a barn that looks like a million soft balls were thrown into the side of it.

Had a metal roof put on my roof last year. I had the Amish put it on and if you know anything about these people, they are the most meticulous with what they do than any contractor I have ever worked with and could not be happier with the end result!

Thad, I have a specific technical question about the soffit, facia, and metal roofing interface. I’ll send your team an email.

They never heard of using head wall flashing, and Z-bar, the ugliest chimney flushing ever

Where can I buy the materials in New Jersey for a New tech machine.?

Why are they kissed so far onto the backup drum. Wouldn’t that have a chance of stalling out the roll and putting cuts and wear lines in the roll?

When it comes to physical testing he dosnt have a clue.

Is the coravent also installed at the roof rakes?

It is disappointing that they do not sell to homeowners

Excellent video, perfect questions and answers, thanks!

Sadly, I don't think the skill level, professionalism and attention to detail shown in this video is the norm. You see this all the time, someone who knows the right people or has the right amount of money can get excellent jobs like this done, but when the rest of us around the country want a job done, its rushed, still costs us ton of money and looks like crap: corners being cut the entire time. Seems the more rural you live, the choices are pretty slim to find contractors, much less a contractor or business who know what they are doing. My sister just sent me pics of her metal roof she had done and it looks awful. Jagged cuts, screws and nails visible everywhere, nothing is seamless and goes into the next piece, open pieces hanging all over the edge, no cohesiveness. By the way, what adhesive caulk are you using?

Thank you for this.

Great info thank you. Can you use any of these panels on a batten-type roof structure either steel or timber? I'm looking at building a Barndominium.

For me,way too much $$$. However, if you own a million dollar home( I do not),I can see doing it.

The only issue I have is the wood 1x4s. They rot. At minimum I would water seal them but I like to rip down 1xX composite boards and use them for the air gap.

What about butyl over sealant?

I can't seem to find a video on how to make a center starter for a snaplock panel. Is it possible to manufacture it by hand after the panel is run or do you need the machine to do it? Any help would be appreciated.

ty

Awesome sir

In Ph, it's akin to plain GI sheet, the only difference is that galvalume is in rolled sheets. We only use this mostly on exterior walls or wooden doors as a protective material during wet seasons (but could be taken as permanent though😁). I think it's not suitable for roofing here...

You see a lot of metal sheeting roofing right on top of the purlins attached to the trusses with no vapor barrier at all.

How can I make my own cleansing solution cause I can't get the cleansweep where I live

The lady in the video is TOTALLY disinterested. Also, I'm not sure why the expert guest speaking failed to mention 40 # felt? It's been out almost as long as 30# felt. What was the warranty on the other two shark products?

19/32 OSB?

Closed Cell Foam under roof sheeting, Peel & Stick on top of roof sheeting, air gap then metal roofing, and an ERV unit. 100%

Wow this is an amazing install video and I admire the craftsmanship. Several questions. The bottom end of the panel? What does the install guide say about dog earing or filing the open area with sealant? The pipes. Wouldn’t sliding those metal covers over them create an ever so small area water could get in from?

Neat. I'm getting a 26 gauge standing seam roof in a month. The guy mentioned getting striated panels to hide the appearance of this. I didn't know it was a thing. Thanks for the little education lesson!

Can you make a video on how to install radiant barrier and roll on insulation? Which one goes on first and the detail steps to it.

Ahhhhhh ....now i know why all of us employees at stone metals got fired... This warehouse used to be Stone Metals, where I worked as the trim lead fabricator. So nice of stone metals owner Brian to put a good word in for me with the new people......great guy .... not really

Прекраснейший станок. 5 лет отработал на таком. Сейчас такой новый не купишь.

Ultraviolet? I would say that is infrared what reflects. UV can't pass through tiles or any roofing cover.

Oh yes, your video on cleaning metal roofs was very informative. Thank you!

Hello. I live in Albion, IN. 46701. Do you know of any reputable metal roof cleaning companies in this area? I have a 2 story lake cottage near sycamore tress. The cottage is 3 years old and the metal roof has never been cleaned. Also, the snow guards are collecting tons of twigs, leaves, etc and is difficult to access. Any references, comments, suggestions would be appreciated. Thank you in advance!😊

Good vid but I don't understand why the screw fastener is installer in the pan rather than the ridge? Water runs downhill, putting the fastener hole where the water gathers and runs seems counter-intuitive? Your thoughts?

Can you walk on the roof without bending the metal?

Just installed a new metal roof on our barn and the manufacturer strongly recommended to never use bleach. His recommendation was to use vinegar.

Dame trabajo